Input channels

3 x AC, ICP® power supply on/off
3 x DC for process values
1 x TACHO for speed probe / external trigger

Input range

AC +/- 12 V peak-peak
DC +/- 24V

AD conversion

24 bit, 64 bit internal signal processing
No AutoGain function!

Dynamic range S/N

120 dB

Frequency ranges (-3 dB)

Maximum range: 0.5 Hz - 25 kHz (64 kHz sampling)
Minimum range: 0.5 Hz - 25 Hz (64 Hz sampling)

Sampling mode

Fully simultaneous for all 3 channels

FFT resolution

Min. 25 lines
Max. 25 600 lines

Measurement modes

Analyzer - analytical measurements
Data collector - route measurements
Balancer - 1 and 2 plane on site balancing
Recorder - raw signal recording for later post analysis
Run Up - run up and coast down measurements
Ultrasound - measurement of ultrasound in 30 - 50 kHz range
LED stroboscope, LED torch
FASIT - Expert system for automatic fault detection
Vibration meter - basic vibration measurements

Software

Free version of DDS software (limited database size)
Licensed DDS software

Data processing

Real time FFT
DEMOD - ENVELOPE analysis
ACMT - low speed bearing analysis
Order analysis
User band pass analysis
RPM measurement
DC measurement
Orbit measurement

IR temperature measurement

From -70˚C to +380˚C (-94˚F to +716˚F)

Trigger

Manual, External, Amplitude, Tacho

Display

Colour 240 x 320 pixels, TFT

Interface

USB 2.0, 3.0 compatible

Operating temperature range

-10˚C to +50˚C

Power

Battery pack for more than 10 hours of continous operation

Case

Aluminium - heavy duty

Weight

780 g

Dimensions

230 x 82 x 32 mm

Main menu

The A4300 VA3 Pro instrument can be configured according to your requirements by choosing measuring modules. There are three free modules included in every VA3: Meter, Fasit and Strobo. Other modules are optional: Analyzer, Route, Balancer, Recorder, Run Up or Ultrasound.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Meter - Free Module!

The Meter module includes basic vibration measurement screens:
- Overall Vibration Values (RMS, 0-PEAK)
- FFT Spectrum
- Time Signal
- Frequency Bands
- Displacement
- Temperature

---------------------------------------------------------------------------------------------------------------------------------------------------------------

FASIT - Free Module!

FASIT (Fault Source Identification Tool) is an expert system for automatic detection of possible machine faults:
- Unbalance
- Misalignment
- Looseness
- Bearing faults

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Strobo - Free Module!

Switch on the stroboscope to visually “freeze” the machine movement and check its rotating parts. The speed of the machine can be detected.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Analyzer

Select the type of the measurement (from simple overall values through FFTs and time signals to more advanced measurements with Proximity probes such as Orbits), set up the measurement settings according to your requirements (frequency range, sampling, units etc.) and take all the predefined measurements simultaneously.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Route

The route module is used for day to day data collection of your factory machinery. Simply create your route tree with measurement points location in the DDS software (possible also in the free DDS version) and take the measurements regularly. Transfer the collected data to DDS software to watch the trends and analyze the data.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Balancer

The balancer allows you to perform one or two plane balancing job of rotating parts such as industrial fans, blowers, spindles etc.

------------------------------------------------------------------------------------------------------------------------------------------------------------------

Recorder

A unique measurement mode with unappreciated value. Recorder “records” the raw signal from the sensor, means raw signal from the machine. This allows to make a post processing of the signal later on your PC. You can play this record again and again and apply any measurement setting to it.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Run up

Similar to Analyzer mode where you can setup any measurement which you like. RunUp allows you to control the saving of data for example as soon as possible, or by speed change, time change etc.

-----------------------------------------------------------------------------------------------------------------------------------------------------------------

Ultrasound

Measurement of sound inaudible to the human ear – ultrasound. Typical application are air leak detection, electrical arcing or early bearing fault detection.