產品介紹∣實驗室濾油裝置
Search

實驗室濾油裝置
CMM-12R OIL REGENERATION SYSTEMS

【Globecore】變壓器油測試儀器 工業用油再生裝置

實驗室濾油裝置

簡介

CMM-0,001U

實驗室СММ-0,001U裝置的目的是測試凈化特定石油化工產品的可能性。

我要諮詢

實驗室СММ-0,001U裝置的目的是測試凈化特定石油化工產品的可能性。
除其他外,可再生和過濾的礦物油類型包括:

  • 工業用油
  • 變壓器油
  • 汽輪機油
  • 柴油
  • 加熱油
  • 液壓油
  • 真空油
  • 精油
  • 傳動油
  • 凝析油
  • 煤油

架構

該單元架構包括:

  • 濾油艙
  • 機架
  • 真空室
  • 真空泵
  • 管道

過濾艙是一個容器,其中一半裝有吸附劑,用於再生過濾油。 吸附劑和油從頂部進入過濾艙。
艙體的底部有一個蓋子,通過這個蓋子艙體被抽真空,並從中提取飽和吸附劑。 再生油也從底部抽出。
艙體的外表面用電熱膠帶包裹並絕緣。
機架是一種金屬結構,支撐著裝置的所有機構。
真空室是一個充滿再生油的矩形容器。 容器頂部裝有一個球閥,用於連接真空泵室。 容器底部亦裝有一個球閥,通過該球閥,油被吸入真空容器,並裝有一個閥門,用於排油。 容器還配有可見的液位計和真空計。
真空泵在真空室中產生真空。

優勢

  • 體積小
  • 便於運輸
  • 可使用於工作間的任何插座電源
  • 測試完畢,可現地直接清洗
  • 超靜音運轉

Parameter

Value

1 Capacity, l/h (gpm)

1000 (4,4)

2 Oil losses during operation, %

2-25

3 Maximum allowed oil temperature, оС (оF)

90 (194)

4 Outlet pressure, bar (psi)

2,5 (36,25)

5 Oil heater power, kW

24

6 Rated vacuum suction speed, l/h (gpm)

280 000 (1232,8)

7 Fuller’s Earth mass, kg (lbs)

1600 (3527,4)

8 Electrical power parameters  
  Voltage, V

Customizable

Frequency, Hz
9 Coarse filtration fineness (mesh filter), µm

100

10 Pre-filtration fineness, µm

25

11 Fine filtration fineness, µm

5

12 Dimensions, mm (in)  
  Length

5500(217)

Width

2320 (91)

Height

2450 (96)

13 Weight, kg (lbs)

6000 (13227)

Regeneration of the oil in a transformer restores used oil to new like condition:

Parameter Before processing After processing
Moisture content by weight,g/t (ppm) as per IEC 733; ASTM D-1533 43 5
ISO 4406 industrial purity class -/18/16 -/14/12
Volumetric gas content % I.A.W.IEC 60599; ASTM D-3612 0.1
Acid number, mg KOH/g I.A.W IEC 296; ASTM D-664 0.2 0.01
Corrosive sulfur  I.A.W.*IEC 5662; ASTM D-1275 present absent
Dielectric strength, kV I.A.W. IEC 156; ASTM D-18116 30 70
Interfacial tension, N/m, at 25ºС  I.A.W.  IEC 6295; ASTM D-664 45
Dissipation factor at 90ºС  I.A.W.IEC 247; ASTM D-924 0.095 0.001
Oxidation stability I.A.W. IEC 74; 164 hours restored

(*I.A.W. In Accordance With)

The GlobeCore regeneration process restores used oils to new like condition.  This process makes it possible to fill transformers with oil that would previously have required disposal.  The oil in the transformer can be used without replacement for the entire service life of the transformer.

The GlobeCore CMM-R systems are designed to extend transformer service life by restoring the dielectric strength and chemical composition of dielectric insulating oil.

In the process of oil regeneration, oil degradation products and acidic compounds are removed, the oil becomes clear, oxidation resistance is improved, while gas solubility is reduced.

Advantages

GlobeCore manufactures oil regeneration systems for both transformer manufacturers and for transformer service providers.

GlobeCore units are loaded with a sorbent that captures all oil decomposition products.

GlobeCore regeneration systems can use the same sorbent for up to 3 years before the first replacement.  No more need for consumables and costly labor related to replacement of exhausted sorbent on the job site.

Regeneration systems can be combined with degassing units or can be purchased as stand-alone systems.

GlobeCore regeneration systems can be used in combination with your existing degassing or drying unit.

Each GlobeCore unit can be customized and includes a number of options:

  • An extra vacuum pump assembly for transformer vacuuming
  • Mounted on a trailer or a semi-trailer
  • Inlet and/or outlet moisture meters for the oil stream
  • Remote control and process monitoring via smartphone or PC
  • Climate Controlled Operator work room.

Parameter

Value

1 Capacity, l/h (gpm)

1000 (4,4)

2 Oil losses during operation, %

2-25

3 Maximum allowed oil temperature, оС (оF)

90 (194)

4 Outlet pressure, bar (psi)

2,5 (36,25)

5 Oil heater power, kW

24

6 Rated vacuum suction speed, l/h (gpm)

280 000 (1232,8)

7 Fuller’s Earth mass, kg (lbs)

1600 (3527,4)

8 Electrical power parameters  
  Voltage, V

Customizable

Frequency, Hz
9 Coarse filtration fineness (mesh filter), µm

100

10 Pre-filtration fineness, µm

25

11 Fine filtration fineness, µm

5

12 Dimensions, mm (in)  
  Length

5500(217)

Width

2320 (91)

Height

2450 (96)

13 Weight, kg (lbs)

6000 (13227)

Regeneration of the oil in a transformer restores used oil to new like condition:

Parameter Before processing After processing
Moisture content by weight,g/t (ppm) as per IEC 733; ASTM D-1533 43 5
ISO 4406 industrial purity class -/18/16 -/14/12
Volumetric gas content % I.A.W.IEC 60599; ASTM D-3612 0.1
Acid number, mg KOH/g I.A.W IEC 296; ASTM D-664 0.2 0.01
Corrosive sulfur  I.A.W.*IEC 5662; ASTM D-1275 present absent
Dielectric strength, kV I.A.W. IEC 156; ASTM D-18116 30 70
Interfacial tension, N/m, at 25ºС  I.A.W.  IEC 6295; ASTM D-664 45
Dissipation factor at 90ºС  I.A.W.IEC 247; ASTM D-924 0.095 0.001
Oxidation stability I.A.W. IEC 74; 164 hours restored

(*I.A.W. In Accordance With)