產品介紹∣變壓器繞組變形分析儀
Search

變壓器繞組變形分析儀
Sweep Frequency Response Analyzer

【DV Power】變電站中各項檢測設備 變壓器繞組變形分析儀

變壓器繞組變形分析儀

簡介

FRA 500

  • 掃描頻率範圍:0.1 Hz – 25 MHz (可選擇)
  • 動態範圍 >140 dB
  • 通訊介面:USB 及藍芽
  • 內建電池 (可選購): 12V, 7Ah 連續工作4小時
  • 典型的掃描時間少於25秒 (20Hz–2MHz)
  • 具雜訊的環境中仍具有出色的頻率響應
  • 每次掃描的採樣點:可選多達32,000
  • 依據C57.149- 2012和DL / T 911-2004標準進行演算
  • 可導入其它廠牌的設備數據進行測試結果比較
  • 分析軟體,具有易於使用的界面以及預定義的測試計劃和報告格式

我要諮詢
  • 掃描頻率範圍和掃描時間
    用戶可以選擇FRA500的掃描範圍:0.1 Hz-25 MHz。 頻率範圍從20 Hz到2 MHz的典型測試掃描時間少於25秒。 可以在10秒內執行快速掃描測試,以確認電纜連接正確。
     
  • 輸出電壓
    FRA500的測試電壓範圍可在0.2 Vpp至20 Vpp的範圍內以0.2 Vpp的步階進行編程。 這使用戶可以將測試電壓與其他製造商的設備執行的測試相對比。
     
  • 動態範圍
    FRA500提供大於140 dB的動態範圍,測量精度為±0.5 db。 較高的動態範圍消除了雜訊的影響,且方便比較不同掃描。
     
  • 電腦介面
    FRA500通過USB或藍牙無線控制。 藍牙功能允許測試人員與變壓器保持適當的距離,以提高安全性和工作效率。
     
  • 內建電池 (可選購)
    提供內建電池 (可選購),該電池最多可提供四個小時的電量。 FRA500所使用的是密封式鉛酸蓄電池(12V,7AH)。
     
  • 自檢測試
    作為隨貨的附件。 用於對設備進行自檢的標準器(請參見下圖)。

在執行完整測試之後,如果單元一切正常,則將顯示以下圖譜:

電源

•輸入電壓:90 – 240 Vac,50/60 Hz。
•輸入功率:50VA。

體積和重量

•體積 (W x H x D): 340x 290 x 150 mm 。
•重量: 4,5 kg。

測量

•掃描頻率範圍:0.1 Hz – 25 MHz。
•取樣率:20Msps。
•每次掃描的採樣點:可選多達32,000點。
•總掃描時間:少於25秒(20Hz– 2MHz)。
•測量/顯示方式:線性/對數。
•輸出電壓:0.2 Vpp – 20 Vpp,步階為0.2 Vpp。
•增益精度:50 dB以上0.5 dB。
•相位精度:50 dB以上0.1º。
•輸入通道:2x50Ω 阻抗。
•輸出通道:1x50Ω 阻抗,短路保護

符合標準

•安規:
–低電壓指令:指令2014/35/EU(CE合格)
–安裝類別II:IEC EN 61010-1標準。

•電磁相容性:
–指令2014/30 / EU(CE合格)
–符合EN 61326-1:2013標準。

介面

藍芽、USB

電池 (選購)

SLA 12V,7Ah,可連續運行4小時

環境條件

•工作溫度:-10ºC– +55ºC。
•存放及運輸溫度:-30ºC– +70ºC。
•濕度:90 RH @ 40ºC,無凝露。

 

 

  • Sweep Frequency Range and Sweep Time
    The FRA500's sweep range is user selectable from 0.1 Hz - 25 MHz. A typical test sweep time, with frequency ranging from 20 Hz to 2 MHz, is less than 25 seconds. A quick sweep test can be performed in under 10 seconds to confirm proper cable connections.
     
  • Output Voltages
    The FRA500's test voltage range is programmable from 0.2 Vpp to 20 Vpp in 0.2 Vpp steps. This enables the user to match the test voltage to tests performed by another manufacturer's device.
     
  • Dynamic Ranges
    The FRA500 offers a dynamic range greater than 140 dB with a measurement accuracy of ±0.5 db. The higher dynamic range eliminates the effects of noise and facilitates the comparison of different sweeps.
     
  • Computer Interfaces
    The FRA500 is computer-controlled via USB or wirelessly via Bluetooth. The Bluetooth feature allows test personnel to be at a comfortable distance from the transformer for increased safety and productivity.
     
  • Optional Battery Backup
    An optional built-in battery backup is also available that can provide power for up to four hours. The FRA500 uses a sealed lead acid battery (12V, 7AH).
  • Mains Power Supply
    Connection: according to IEC/EN60320-1; UL498, CSA 22.2
    Mains supply: 90 – 240 Vac, 50/60 Hz
    Input power: 50VA
    Fuse: T5L250V
     
  • Measurement
    Sweep frequency range: 0,1 Hz – 25 MHz
    Sampling rate: 100 mega samples per second
    Sample points per sweep: 2 000 points per decade, 32 000 points total
    Total sweep time: less than 25 seconds (20Hz – 2MHz)
    Point spacing: log or linear
    Output voltage: 0.2 Vpp – 20 Vpp in 0.2 Vpp steps
    Gain accuracy: 0.5 dB above 50 dB
    Phase accuracy: 0.1 degree above 50 dB
    Input channels: 2x50 Ohm impedance
    Output channels: 1x50 Ohm impedance, short-circuit protected
     
  • Interface
    Bluetooth
    USB
     
  • Environmental Conditions
    Operating temperature:
    - 10 ºC – +55 ºC / 15 ºF – +122 ºF
    Storage temperature:
    - 30 ºC – +70 ºC / -22 ºF – +158 ºF
    Humidity: 90% RH @ 40 ºC (104ºF) non-condensing
    Altitude: 2 000m (6562 ft.)
     
  • Dimensions and Weight
    Dimensions (W x H x D): x 290 x 150 mm / 13 x 11 x 6 in
    Weight: 4,5 kg / 10.0 lbs.
     
  • Battery (optional)
    SLA 12V, 7Ah for 4 hours of continuous operation
     
  • Applicable Standards
    Safety: LVD 2014/35/EU (CE Conform), Standards EN 61010-1:2010
    EMC: Directive 2014/30/EU (CE Conform), Standard EN 61326-1:2013