簡介
CAT 100 Series
CAT100 系列繼承了市場領先的 CAT 標準系列的所有功能和經驗。
每台 CAT100 系列設備（3 或 6 個主接點通道）都可使用內置電池供電，可工作長達 8 小時。
CAT100 採用特有的觸控螢幕界面，可大大節省各類中壓和高壓斷路器的測試準備和結果分析時間。通過視覺式的 7" 彩色觸控螢幕，可使CAT100 以獨立設備的形式分析圖形和數字結果。
CAT100 系列繼承了市場領先的 CAT 標準系列的所有功能和經驗。
每台 CAT100 系列設備（3 或 6 個主接點通道）都可使用內置電池供電，可工作長達 8 小時。
CAT100 採用特有的觸控螢幕界面，可大大節省各類中壓和高壓斷路器的測試準備和結果分析時間。通過視覺式的 7" 彩色觸控螢幕，可使CAT100 以獨立設備的形式分析圖形和數字結果。
CAT100 系列可以記錄：
- 最多可同時對6 個主接點（每相 2 個斷口）的開關動作時間測量，還包括預插入電阻（如果斷路器中存在）和 4 個輔助觸點。
- 測量預插入電阻（如果斷路器中存在）的電阻值。
- 同時測量兩個線圈電流（跳閘和合閘）。
- 最多可測量四個類比訊號（變電站所內電壓、馬達電壓或任何其它類型的類比訊號）。
- 測量斷路器運動機件的位移、接觸摩擦、超程、回彈、阻尼時間和平均速度。
測試結果以表格和圖形形式列印在 58 mm（2.28 英寸）熱感式列表機（選購配件）上。
| Main contact inputs • Number of contact inputs: up to 6(3x2), 2 per phase • Each channel detects Main and pre-insertion resistor contacts.
Short circuit current 50 mA • Each channel measures resistance of preinsertion resistors |
Coil driver • Number of channels: 2 (Trip and Close coil) • Two separate outputs for coil triggering • Driver characteristics: 300 V DC max, 35 A DC max • Electronic drivers provide superior timing control • Overcurrent and overvoltage protection • Coil supply input: 300 V DC max, 35 A DC max |
|
| Auxiliary inputs • Number of channels: 4, galvanically isolated • User selectable: dry or wet
|
Current measurement • Current measurement for Trip and Close coil, 2 channels, Hall-Effect sensor • Range ±35 A DC to 5 kHz • Accuracy: ± (0,5 % rdg + 0,1 % FS) • Graphic presentation: currents waveform is displayed with a resolution of 0,1 ms |
|
| Analog inputs • 2 channels – Coil current measurement • 4 Voltage channels, each channel has four measurement ranges: ±1 V, ±5 V, ±60 V and ±300 V AC/DC The analog inputs are isolated with respect to all other circuits |
||
| Time measurement Time measurement resolution: • 0.025 ms for 1 s test duration (sampling rate 40 kHz) • 0,1 ms for 2 s test duration (sampling rate 10 kHz) • 1 ms for 20 s test duration (sampling rate 1 kHz) • 10 ms for 200 s test duration (sampling rate 100 Hz) Time accuracy: 0,05% of the reading ± resolution |
DC output 24 V voltage supply for current clamps |
|
| PC Interface • USB • Ethernet |
||
| Display • Touch screen color display 7 inch. |
||
| Breaker operation • Close (C) • Open (O) • Close-Open (C-O) • Open-Close (O-C) • Open-Close-Open (O-C-O) The user can select any desired test sequence |
Mains power supply • Connection according to IEC/EN60320-1; UL498, CSA 22.2 • Mains supply: 90 V - 264 V AC • Frequency: 50/60 Hz • Input power: 250 VA |
|
| Printer (optional) • Thermal printer • Graphic and numeric printout • Paper width 58 mm (2.28 in) • Printer operating temperature: - 20 ºC - + 70 ºC / - 4 ºF - +158 ºF |
Internal battery supply (optional) • Built-in rechargeable battery • Li-Ion 14.4 V Cell – 6800 mAh 98 Wh |
|
| Transducer input • Digital transducer inputs: 1 • Analogue transducer inputs: 1 |
Applicable standards • Installation / Overvoltage: Category II • Pollution: Degree 2 • Safety: LVD 2014/35/EU (CE Conform) Standard EN 61010-1 • EMC: Directive 2014/30/EU (CE Conform) Standard EN 61326-1 • CAN/CSA-C22.2 No. 61010-1 |
|
| Time measurement triggers • External trigger: 2 channels (trigger input voltage: 10 V – 300 V AC/DC) • Coil currents: threshold level user selectable • Auxiliary inputs (change of contacts state) |
||
| Dimensions and weight • Dimensions (W x H x D): o 503 mm x 406 mm x 193 mm 19.8 in x 15.9 in x 7.6 in • Weight: o 8.5 kg / 18.7 lbs. |
Environmental conditions • Operating temperature: - 20 ºC to + 55 ºC / - 4 ºF to + 131 ºF • Storage & transportation: - 40 ºC to + 70ºC / - 40 ºF to + 158 ºF • Humidity 0 % - 95 % relative humidity, noncondensing |
The CAT100 Series inherited all capabilities and experience collected from the market-leading CAT Standard Series.
Each CAT100 Series device (3 or 6 timing channels) can be supplied with an internal battery power supply that enables up to 8 hours of operation.
CAT100 introduces a unique touchscreen interface designed to significantly save the time required for test preparation and results analysis of all types of medium- and high-voltage circuit breakers. The graphical and numerical results can be analyzed using the standalone CAT100 device via the intuitive 7” color touch-screen display.
The CAT100 Series can record:
- Simultaneous timing measurement of up to 6 main contacts (2 breaks per phase) including pre-insertion resistors (if present in the circuit breaker) and four auxiliary contacts.
- Resistance measurement of the pre-insertion resistors (if present in the circuit breaker).
- Simultaneous measurement of two coil currents (Trip & Close).
- Measurement of up to four analog signals (substation battery, motor voltage, or any other type of analog signal).
- Measurement of displacement, contact wipe, over-travel, rebound, damping time, and average velocity of the breaker’s moving parts.
Test results are printed on the 58 mm (2.28 inch) thermal printer (optional accessory) in tabular and graphical form.
| Main contact inputs • Number of contact inputs: up to 6(3x2), 2 per phase • Each channel detects Main and pre-insertion resistor contacts.
Short circuit current 50 mA • Each channel measures resistance of preinsertion resistors |
Coil driver • Number of channels: 2 (Trip and Close coil) • Two separate outputs for coil triggering • Driver characteristics: 300 V DC max, 35 A DC max • Electronic drivers provide superior timing control • Overcurrent and overvoltage protection • Coil supply input: 300 V DC max, 35 A DC max |
|
| Auxiliary inputs • Number of channels: 4, galvanically isolated • User selectable: dry or wet
|
Current measurement • Current measurement for Trip and Close coil, 2 channels, Hall-Effect sensor • Range ±35 A DC to 5 kHz • Accuracy: ± (0,5 % rdg + 0,1 % FS) • Graphic presentation: currents waveform is displayed with a resolution of 0,1 ms |
|
| Analog inputs • 2 channels – Coil current measurement • 4 Voltage channels, each channel has four measurement ranges: ±1 V, ±5 V, ±60 V and ±300 V AC/DC The analog inputs are isolated with respect to all other circuits |
||
| Time measurement Time measurement resolution: • 0.025 ms for 1 s test duration (sampling rate 40 kHz) • 0,1 ms for 2 s test duration (sampling rate 10 kHz) • 1 ms for 20 s test duration (sampling rate 1 kHz) • 10 ms for 200 s test duration (sampling rate 100 Hz) Time accuracy: 0,05% of the reading ± resolution |
DC output 24 V voltage supply for current clamps |
|
| PC Interface • USB • Ethernet |
||
| Display • Touch screen color display 7 inch. |
||
| Breaker operation • Close (C) • Open (O) • Close-Open (C-O) • Open-Close (O-C) • Open-Close-Open (O-C-O) The user can select any desired test sequence |
Mains power supply • Connection according to IEC/EN60320-1; UL498, CSA 22.2 • Mains supply: 90 V - 264 V AC • Frequency: 50/60 Hz • Input power: 250 VA |
|
| Printer (optional) • Thermal printer • Graphic and numeric printout • Paper width 58 mm (2.28 in) • Printer operating temperature: - 20 ºC - + 70 ºC / - 4 ºF - +158 ºF |
Internal battery supply (optional) • Built-in rechargeable battery • Li-Ion 14.4 V Cell – 6800 mAh 98 Wh |
|
| Transducer input • Digital transducer inputs: 1 • Analogue transducer inputs: 1 |
Applicable standards • Installation / Overvoltage: Category II • Pollution: Degree 2 • Safety: LVD 2014/35/EU (CE Conform) Standard EN 61010-1 • EMC: Directive 2014/30/EU (CE Conform) Standard EN 61326-1 • CAN/CSA-C22.2 No. 61010-1 |
|
| Time measurement triggers • External trigger: 2 channels (trigger input voltage: 10 V – 300 V AC/DC) • Coil currents: threshold level user selectable • Auxiliary inputs (change of contacts state) |
||
| Dimensions and weight • Dimensions (W x H x D): o 503 mm x 406 mm x 193 mm 19.8 in x 15.9 in x 7.6 in • Weight: o 8.5 kg / 18.7 lbs. |
Environmental conditions • Operating temperature: - 20 ºC to + 55 ºC / - 4 ºF to + 131 ºF • Storage & transportation: - 40 ºC to + 70ºC / - 40 ºF to + 158 ºF • Humidity 0 % - 95 % relative humidity, noncondensing |